Milk Stool | Build It | Ask This Old House

Build It
In this video, general contractor Tom Silva shows how to take reclaimed lumber and turn it into a charming milk stool for children or decor.

SUBSCRIBE to This Old House: http://bit.ly/SubscribeThisOldHouse.

General contractor Tom Silva and host Kevin O’Connor meet back at the shop for a unique project. Tom has some reclaimed lumber on hand that he plans to turn into a milking stool.

Difficulty: ⅗
Cost: Under $100 (provided you own the tools)
Time: One day

How to Build a Milk Stool
Note: This project requires two slabs of wood, approximately 20 by 24 by around 3 inches thick, whether reclaimed chunks or pieces of construction lumber glued together. It’s possible to cut old beams into slabs and glue them together or purchase whole pieces of wood made from hemlock, pine, or other species from lumberyards.
Note: Whenever removing parts from the lockset or the door, place them in a small container. These parts can be easy to lose and expensive to replace.
1. Pass the slabs of wood through the planer until the surface is flat. If a slab wobbles, hold it against the table’s surface and glue a straight piece of wood to one edge until the board is stable, and then pass it through the planer. This will result in a perfectly flat, even edge. Turn the slabs over and pass them through the planer until they reach the desired thickness (about 2 inches).
2. Create a jig from a strip of thin plywood. Drill a hole to the same diameter as the router’s template collar, measure exactly 6-inches from the inside of the hole to the middle of the plywood, and drill a small hole. You’ll use this to cut the seat.
3. Place the small hole of the template in the middle of one of the slabs and drive a small screw to act as an anchor. Make several passes around the slab with the router, milling progressively deeper with each pass. Continue until the router can’t cut any deeper, and cut off the excess wood with a jigsaw.
4. Remove the template and swap the router bit for a flush-cut bit with a bearing on the end. Turn the slab over so it’s face down, and run the router around the rest of the slab to remove the rest of the wood. Switch to a roundover bit and mill a smooth, rounded edge around the seat on both sides.
5. Turn the other slab on its edge and pass it over the benchtop joint to create one true, 90-degree edge. Be sure to hold the flattened, planed edge against the fence for accurate milling.
6. Place the 90-degree edge against the table saw bed and fence and cut the board into rough dimensions (approximately 2 ½ inches). Run these boards over the jointer to square them up, before bringing them back to the table saw for the final cut (about 2 inches for the rails and 2 ¼ inches for the legs).
7. Adjust the compound miter saw to 8 degrees in both directions. Cut the rails to length (around 5 inches) and cut the legs to length (around 12 to 16 inches). This should create splayed legs that provide a wider footprint and stability.
8. Cut mortises for floating tenons, one in the end of each rail, and two in each leg. Fill the mortises with glue, place the floating tenons inside, assemble the legs, and allow the glue to dry.
9. Flip the seat so the screw hole in the center is facing up, and place the chair leg assembly on top. Center the assembly, pre-drill holes in each corner (two per rail), and drive screws through the rails to fasten them to the seat.

Looking for more step by step guidance on how to complete projects around the house? Join This Old House Insider to stream over 1,000 episodes commercial-free: https://bit.ly/2GPiYbH

Plus, download our FREE app for full-episode streaming to your connected TV, phone or tablet: https://www.thisoldhouse.com/pages/streaming-app

Materials:
Wood glue [https://amzn.to/3MJkMzX]
Screws [https://thd.co/39QxVsq]
Wood slabs [https://thd.co/3GdmreV]

Tools:
Thickness planer [https://amzn.to/3lC49dT]
Router with template collar and router bits [https://amzn.to/3wJ4nGi]
Jigsaw [https://amzn.to/39QAk6q]
Benchtop jointer [https://amzn.to/3wQ8jDW]
Table saw [https://amzn.to/3Nwy8jd]
Compound miter saw [https://amzn.to/3MKj7Kx]
Power drill [https://amzn.to/3NxTHzR]
Tenon mortiser [https://amzn.to/3GhqrLx]

Build It:
This Old House general contractor Tom Silva, This Old House host Kevin O’Connor, and special guests including Jimmy DiResta, take you through step-by-step DIY projects in this popular video series. From end-tables to cutting boards to wine racks to chicken coops and more, learn how to build from the best pros in the game. Segments include mention of all tools and materials needed to get the job done.

Follow This Old House:
Facebook: http://bit.ly/ThisOldHouseFB
Twitter: http://bit.ly/ThisOldHouseTwitter
Pinterest: http://bit.ly/ThisOldHousePinterest
Instagram: http://bit.ly/ThisOldHouseIG

Milk Stool | Build It | Ask This Old House
https://www.youtube.com/user/thisoldhouse/

Products You May Like

Articles You May Like

This Is The Point Where I Second Guess My Decisions
My Finished (For The Most Part) Studio Office Area Cabinets!
The Second Studio Countertop Is Finished!
5 Ways to Do Sublimation with No Printer!
Studio Sconce Makeover — From Black To White With Gold Leaf Accents

Leave a Reply

Your email address will not be published. Required fields are marked *